- Home
- ELECTRONICS
- FLIGHT CONTROLLER Matek H743-SLIM
FLIGHT CONTROLLER Matek H743-SLIM
type: Electronics
Vendor: Dronebuildz.com
Description:
FC Specifications
- MCU: STM32H743VIH6, 480MHz , 1MB RAM, 2MB Flash
- Board V1.0 IMU: MPU6000 (SPI1) & ICM20602 (SPI4)
- Board V1.5 IMU: MPU6000 (SPI1) & ICM42605 (SPI4)
- Baro: Infineon DPS310 (I2C2)
- OSD: AT7456E (SPI2)
- Blackbox: MicroSD card socket (SDIO)
- 7x Uarts (1,2,3,4,6,7,8) with built-in inversion.
- 13x PWM outputs(including “LED” pad)
- 2x I2C
- 1x CAN
- 6x ADC (VBAT, Current, RSSI, Analog AirSpeed, Vbat2, Cur2)
- 3x LEDs for FC STATUS (Blue, Red) and 3.3V indicator(Red)
- 1x SPI3 breakout
- USB Type-C(USB2.0)
- 1x JST-SH1.0_8pin connector (Vbat/G/Curr/Rx8/S1/S2/S3/S4)
- 1x JST-GH1.25_4pin connector (5V/CAN-H/CAN-L/G)
- Dual Camera Inputs switch
- 5V/Vbat filtered power ON/OFF switch
- DJI FPV OSD is supported by any spare UART
Power
- Vbat Input: 6~36V (2~8S LiPo)
- BEC: 5V 2A cont. (Max.3A)
- LDO 3.3V: Max.200mA
- No Current Sensor built-in
- ADC Vbat2 pad supports Max. 69V (voltage divider: 1K:20K)
- Static power: 200mA@5V with Betaflight, 150mA@5V with ArduPilot
FC Firmware
- ArduPilot(ChiBiOS): MATEKH743
- BetaFlight: MATEKH743
- INAV: MATEKH743
Physical
- Mounting: 30.5 x 30.5mm, Φ4mm with Grommets Φ3mm
- Dimensions: 36 x 36 x 5 mm
- Weight: 7g
Including
- 1x H743-SLIM
- 6x Silicon grommets M4 to M3
- 1x JST-SH1.0_8pin cable, 5cm
- 2x JST-SH1.0_8pin connectors
- 1x JST-GH-4P to JST-GH-4P cable for CAN port, 20cm
Other fine products
Categories
- 3D Printing Spare Parts (4)
- ACCESSORIES (3)
- AGRICULTURAL / COMMERCIAL DRONES (1)
- BATTERIES (24)
- ELECTRONIC SPEED CONTROLLERS (35)
- ELECTRONICS (114)
- FLIGHT CONTROLLERS (25)
- FPV ANTENNAS (11)
- FPV CAMERAS (10)
- FPV EQUIPMENT (43)
- FPV RECEIVERS (1)
- FPV TRANSMITTERS (9)
- FRAMES/FRAME PARTS (19)
- MISC (0)
- MOTORS (33)
- PROPELLERS (46)
- RC ANTENNAS (2)
- RC RECEIVERS (1)
- RC TRANSMITTERS (1)
- READY TO FLY (4)
- Street league (0)
- X CLASS (31)